Archives des 5.2 Spatter Protection - PSA https://psa-paris.com/project-category/5-welding-metal-treatment/5-2-spatter-protection/ Produits Sanitaires Aéronefs - PSA Sat, 13 Apr 2024 10:17:05 +0000 en-US hourly 1 https://wordpress.org/?v=6.8.1 S-WELD SPATTER GUARD https://psa-paris.com/products/s-weld-spatter-guard-250/ Mon, 27 Nov 2023 10:32:31 +0000 https://psa-paris.com/products/s-weld-spatter-guard-250/ L’article S-WELD SPATTER GUARD est apparu en premier sur PSA.

]]>

S-WELD SPATTER GUARD

Anti-Spatter Aerosol

  • Protection for interior and exterior of MIG nozzles & Electrode welding.
  • Uniform spray with no air bubbles.
  • Non-flammable, making it workshop safe.
  • Provides base metal protection and can be used in all areas.
  • Contains no silicones which enables no painting or powder coating problems.
TECHNICAL DATASHEET
ASK FOR QUOTE OR DETAILS

DESCRIPTION

S-Weld Spatter Guard is a paintable, cost-effective and non-flammable agent for the prevention of weld-spatter adhering to metal surfaces during the welding process. S-Weld Spatter Guard avoids the need for mechanical abrasion or grinding of weld spatter following welding. It contains corrosion inhibitors for base metal protection. S-Weld Spatter Guard increases the life cycle of torch components saving time and money. It eliminates spatter build-up which results in poor gas flow causing pitting and porosity.

S-Weld Spatter Guard is suitable for a wide range of steels, including mild steel, stainless, steels, aluminium and high-performance alloys.

APPLICATION AREAS

APPLICATION FOR WELDING TORCH:

Spray S-Weld Spatter-Guard before welding in a thin and uniform film onto the areas to be protected. Hold spray can approximately 30cm from the surface to be protected. Also use the spray to protect the interior and exterior of nozzles, the end and outer surface of contact tips, and all other potential areas which are subject to weld spatter. It may be advisable to spray diffusers and the base of the nozzle support as well.

APPLICATION FOR BASE METAL:

Spray S-Weld Spatter-Guard hold spray can approximately 30cm from surface to be protected. Spray a thin uniform coating.

DIRECTIONS FOR USE

Spray onto the area to be treated, in a thin and uniform film, holding the nozzle approximately 30cm from the surface. NOTE: Wipe surface with a clean cloth to remove S-Weld Spatter Guard anti-spatter spray prior to painting.

APPROVALS

No information

PHYSICAL PROPERTIES

Appearance: Clear Amber

Colour: White to Medium Amber

Odour: Match Std.

Specific Gravity: 1.29 ± 0.05 g/cc

% Volatiles: 92-96%

Viscosity: 0.43

ORDERING INFO

CodePackagingUnits/Carton
1450/454454g aerosol can12 units

L’article S-WELD SPATTER GUARD est apparu en premier sur PSA.

]]> CALGUARD CONCENTRATE RED https://psa-paris.com/products/calguard-concentrate-red-248/ Mon, 27 Nov 2023 10:32:30 +0000 https://psa-paris.com/products/calguard-concentrate-red-248/ L’article CALGUARD CONCENTRATE RED est apparu en premier sur PSA.

]]>

CALGUARD CONCENTRATE RED

Concentrated Water-Based Anti-Spatter Spray

  • Non-toxic & water based, making it user safe.
  • Biodegradable, easy waste disposal.
  • Non-flammable.
  • Paintable – no silicone.
TECHNICAL DATASHEET
ASK FOR QUOTE OR DETAILS

DESCRIPTION

CalGuard concentrate is a concentrated water-based anti-spatter spray used for protecting metal surfaces from weld spatter during welding.

APPLICATION AREAS

No information

DIRECTIONS FOR USE

Dilute before using by adding 1 part of CalGuard Concentrate to 3 parts water.

Spray CalGuard Anti-Spatter Spray before welding in a thin and uniform film onto the areas to be protected. Be sure to spray approximately 30cm from the areas to be protected.

Also use the spray to protect the interior and exterior of nozzles, the end and outer surface of contact tips, and all other potential areas which are subject to weld spatter.

It is advisable to spray diffusers and the base of the nozzle support as well.

WASH DOWN: To remove CalGuard Anti-Spatter Spray after use, clean the surface with a steel compatible degreaser.

APPROVALS

No information

PHYSICAL PROPERTIES

No information

ORDERING INFO

CodePackagingUnits/Carton
1410/5120 litresEach
1410/64200 litresEach
1410/10001000 litresEach

L’article CALGUARD CONCENTRATE RED est apparu en premier sur PSA.

]]> CALGUARD NOZZLE DIP GEL https://psa-paris.com/products/calguard-nozzle-dip-gel-249/ Mon, 27 Nov 2023 10:32:30 +0000 https://psa-paris.com/products/calguard-nozzle-dip-gel-249/ L’article CALGUARD NOZZLE DIP GEL est apparu en premier sur PSA.

]]>

CALGUARD NOZZLE DIP GEL

Prevents Spatter Adhering to Sensitive Components

  • Non-toxic, making it user friendly.
  • Ready to use without any mixing.
  • Controlled usage, allowing for no wastage.
  • Silicone free – paintable.
  • Ideal for steel, aluminium and alloys.
TECHNICAL DATASHEET
ASK FOR QUOTE OR DETAILS

DESCRIPTION

CalGuard Nozzle Dip Gel is an advanced, non-toxic, nozzle dip gel for the prevention of spatter adhering to sensitive components of welding torches. Including the interior and exterior of MIG nozzles, the end and outer surfaces of contact tips and positional and fixtures.

APPLICATION AREAS

No information

DIRECTIONS FOR USE

1. Ensure the nozzle is clean and free from weld spatter before starting.

2. Replace the worn components before starting.

3. Start to weld briefly to heat the nozzle.

4. When the nozzle is hot dip it into the Cal-Guard gel.

5. Drain any excess gel off if necessary.

6. Continue to re-dip the nozzle into the gel to maintain an even coat, do this as required.

7. Avoid the build-up of Cal-Guard Nozzle Dip Gel in the diffuser by storing the torch in a downward direction when not in use.

APPROVALS

No information

PHYSICAL PROPERTIES

Specific Gravity: 0.82

Boiling Point: >350⁰C

Flash Point (Deg C): > 220 (PMCC)

Appearance: Blue gel

Solubility in water: Miscible

ORDERING INFO

CodePackagingUnits/Carton
1460/400400-grams12 units

L’article CALGUARD NOZZLE DIP GEL est apparu en premier sur PSA.

]]> CALGUARD ANTI-SPATTER SPRAY https://psa-paris.com/products/calguard-anti-spatter-spray-246/ Mon, 27 Nov 2023 10:32:29 +0000 https://psa-paris.com/products/calguard-anti-spatter-spray-246/ L’article CALGUARD ANTI-SPATTER SPRAY est apparu en premier sur PSA.

]]>

CALGUARD ANTI-SPATTER SPRAY

Anti-Spatter Spray

  • Non-toxic & water based, making it user safe.
  • Biodegradable, easy waste disposal.
  • Non-flammable.
  • Paintable – no silicone.
TECHNICAL DATASHEET
ASK FOR QUOTE OR DETAILS

DESCRIPTION

CalGuard Anti-Spatter Spray is a water based, paintable, cost effective and non-flammable agent for the prevention of weld-spatter adhering to metal surfaces during the welding process. It eliminates spatter build up which results in poor gas flow causing pitting, porosity and costly rework.

APPLICATION AREAS

A handheld spray applicator can be used for welding torch components and base metal areas. For larger areas, wiping and mopping may be used. To remove CalGuard Anti-Spatter after use, clean the surface with a suitable detergent or solvent cleaner.

DIRECTIONS FOR USE

Welding Torch:

Spray CalGuard Anti-Spatter before welding in a thin and uniform film onto the areas to be protected. Hold spray can or applicator approximately 30cm from the surface to be protected. Also use the spray to protect the interior and exterior of nozzles, the end and outer surface of contact tips, and all other potential areas which are subject to weld spatter. It may be advisable to spray diffusers and the base of the nozzle support as well.

Base Metals – Jigs – Clamps – Bench Tops:

Spray CalGuard Anti-Spatter spray can or applicator approximately 30cm from surface to be protected. Spray a thin uniform coating. As with any form of anti-spatter do not over apply solution as excessive solution application may be detrimental to the weld quality. Note: Prior to painting wipe with surface with a suitable degreasing agent.

APPROVALS

No information

PHYSICAL PROPERTIES

Appearance: Water

Solubility: Miscible

Boiling Point (Deg°C): 100°C

Specific Gravity: 1.008g/ml

ORDERING INFO

CodePackagingUnits/Carton
1400/28750ml12
1400/425 litres4
1400/5120 litresEach
1400/64200 litresEach

L’article CALGUARD ANTI-SPATTER SPRAY est apparu en premier sur PSA.

]]> CALGUARD ANTI-SPATTER AEROSOL https://psa-paris.com/products/calguard-anti-spatter-aerosol-247/ Mon, 27 Nov 2023 10:32:29 +0000 https://psa-paris.com/products/calguard-anti-spatter-aerosol-247/ L’article CALGUARD ANTI-SPATTER AEROSOL est apparu en premier sur PSA.

]]>

CALGUARD ANTI-SPATTER AEROSOL

Anti-Spatter Spray Aerosol

  • Non-toxic & water based, making it user safe.
  • Biodegradable, easy waste disposal.
  • Non-flammable.
  • Paintable – no silicone.
  • For MIG & Electrode welding.
TECHNICAL DATASHEET
ASK FOR QUOTE OR DETAILS

DESCRIPTION

CalGuard Anti-Spatter Spray is a water based, paintable, cost effective and non-flammable agent for the prevention of weld-spatter adhering to metal surfaces during the welding process. It eliminates spatter build up which results in poor gas flow causing pitting, porosity and costly rework.

APPLICATION AREAS

A handheld spray applicator can be used for welding torch components and base metal areas. For base metal, larger areas, wiping and mopping may be used. To remove CalGuard Anti-Spatter after use, clean the surface with a suitable detergent or solvent cleaner.

DIRECTIONS FOR USE

Welding Torch:

Spray CalGuard Anti-Spatter before welding in a thin and uniform film onto the areas to be protected. Hold spray can or applicator approximately 30cm from the surface to be protected. Also use the spray to protect the interior and exterior of nozzles, the end and outer surface of contact tips, and all other potential areas which are subject to weld spatter. It may be advisable to spray diffusers and the base of the nozzle support as well.

Base Metals – Jigs – Clamps – Bench Tops:

Spray CalGuard Anti-Spatter spray can or applicator approximately 30cm from surface to be protected. Spray a thin uniform coating. As with any form of anti-spatter do not over apply solution as excessive solution application may be detrimental to the weld quality. Note: Prior to painting wipe with surface with a suitable degreasing agent.

APPROVALS

No information

PHYSICAL PROPERTIES

Appearance: Water

Solubility: Miscible

Boiling Point (Deg°C): 100°C

Specific Gravity: 1.008g/ml

ORDERING INFO

CodePackagingUnits/Carton
1400/400400ml12

L’article CALGUARD ANTI-SPATTER AEROSOL est apparu en premier sur PSA.

]]>