No information

One bottle of ROX® Pro Engine Anti-wear can treat up to 10 Litres of engine oil.

No information

Appearance: Clear amber liquid

Density: 0.95 ± 0.02 g/mL

Code	Packaging
8296/300	300mL
8296/30	1L
8296/42	5L

200mL of Rox® Diesel BioAttack treats 1,000 litres of fuel, or 1L of Rox® Diesel BioAttack treats 5,000 litres of fuel.

Add required amount to fuel tank prior to filling up tank; addition of new fuel will mix and agitate ROX® 4300 through the fuel to give a homogenous dispersion.

Dose the fuel every time you put fresh fuel into the tank otherwise bacteria growth may start again.

NOTE: WATCH FILTERS – Once you have started treating a contaminated fuel system check your filters regularly. Once the Diesel Fuel Biocide kills the organisms, they will dislodge from the sides and bottom of the fuel tank and from pipes and mix with the fuel, passing to the filter. Clean out filters regularly.

No information

No information

Character: Hydrocarbon petroleum solvent

Appearance: Clear and amber liquid

Specific Gravity: Clear

Shelf life: 24 months if stored in closed drum

Code	Packaging
8286/30	1L
8286/42	5L
8286/51	20L

1L of ROX® Diesel Preserver can treat 1000L of diesel.

Add the required quantity of ROX® Diesel Preserver to the storage vessel halfway through filling with diesel.

The addition of the remaining diesel will ensure sufficient turbulence to cause ROX Diesel Preserver to be dosed equally throughout the storage vessel.

No information

Colour: Dark brownTransparency: ClearDensity: 0.88 g/mL ± 0.02 g/mL

Code	Packaging
8287/30	1L
8287/42	5L
8287/51	20L

No information

° Ensure the engine is not running, add contents (300mL) to crankcase.

° Idle engine for 5 to 15 minutes, turn engine off and drain crankcase while oil is still hot.

° Replace oil plug, install new filter, and add new oil.

No information

Appearance: Brown liquid with petroleum odour, does not mix with water.

Transparency: Clear

Density at 20oC: 0.81 ± 0.01

Code	Packaging
8290/300	300mL
8290/30	1L
8290/42	5L
8290/51	20L

HAND WIPE APPLICATION:

• Mix 1 part of metal cleaner with 1 part of clean water.

• Wet surface with a sponge or rag and follow immediately by scrubbing with a stainless steel Scotch Brite type pad.

• Rinse with clean water once all traces of corrosion are removed.

SPRAY APPLICATION:

• Mix one part of metal cleaner with 1 to 2 parts of clean water.

• Spray onto surface with an acid resistant spray pump.

• Where appropriate, scrub the surface with a Scotch Brite pad.

• For hard to use areas, use a high-pressure spray containing a 10% solution of metal cleaner.

• Rinse thoroughly with clean water when all visible traces of corrosion have been removed.

1. General Surface Cleaning After Fabrication: Mix 1 part of metal cleaner with 5 to 8 parts of water at room temperature. Spray onto surface by acid resistant spray pump. Some brushing of the surface will assist with removal of corrosion and difficult soils. The surface should be kept wet with the solution until the soil is gone. Rinse the surface; warm water is preferred.

2. Corrosion Removal: Where the surface of handrails, stainless steel cladding or process plant and carbon steel equipment shows visible signs of corrosion (rusting).

No information

Specific Gravity: 1.35

Appearance: Colour Water White

Code	Packaging
8246/30	1L
8246/42	5L

No information

It is important to add ROX® Diesel Anti-freeze to the fuel when the temperature of the fuel is above its cloud point.

• Dose the fuel at the terminal or directly into the vessel fuel tank.

• Add the ROX® Diesel Anti-freeze to the fuel prior to topping up with the new fuel delivery. The turbulence will successfully mix the ROX® Diesel Anti-freeze through the fuel.

• Alternatively, the ROX® Diesel Anti-freeze can be added at any time to the fuel in storage and action of recirculating will ensure adequate dispersion.

A dosage rate of 1 litre ROX® Diesel Anti-freeze to 500 litres of MGO or diesel fuel is required for the coldest climates.

A dosage of up to 1:1000 is acceptable in milder temperature ranges.

See test results on Technical Data Sheet.

Density at 20°C: 0.89 ± g/mL

Colour: Yellow

Transparency : Clear to slightly hazy

Code	Packaging
8250/42	5L
8250/51	20L
8250/64	200L
8250/1000	1000L

No information

The recommended treat rate is 1:500 for the initial first-time treatment and 1:1000 to 1:2000 for subsequent treatments.

• Add 1 part of Diesel Fuel Additive to 500 parts of Diesel for the first treatment. Mix well.

• For subsequent treatment add 1 part to 1000 parts of Diesel.

No information

Appearance colour: Light brown

coloured liquid

Density: 0.82 +/- 0.02

Transparency: Clear

Code	Packaging
8285/30	1L
8285/42	5L
8285/51	20L

No information

A ready to use formulation.

Use brush or spray on.

No information

Appearance: Clear blue Solution

Specific Gravity: 1.03 at 20°C (gms/mL)

Odour: Coconut

Code	Packaging
8241/30	1L

• Generally used at a concentration of 5-10% (1 part Rox® Care Truck Wash: 20 parts water, to 1 part Rox® Care Truck Wash: 10 parts water).

• Can be used neat as a degreaser.

• When using a high pressure cleaner, the dose rate is 10-20 ml/litre of water (1 part Rox® Care Truck Wash: 100 parts water).

• If time permits sponge or brush surface. If not, allow to penetrate for as long as possible.

• Hose or pressure rinse away all residual suds. It is most effective to rinse from the bottom up to the top and back down to the bottom again. This rinses soils from crevices.

• If practical, chamois all paintwork for a great result.

Rox® Care Truck wash is a high foaming product that can be applied via High Volume (HV) and Low Volume (LV) foamers, sponged, broomed, or sprayed onto bodywork, glass, and aluminium.

Rox® Care Truck Wash It has remarkable rinsing capabilities and will not streak when hosed effectively.

Rox® Care Truck Wash car wash is also suitable for use in automatic truck wash installations.

No information

Appearance: Thick blue liquid

Specific gravity: 1.015

pH (100%): 11.5 ± 0.5

Solubility in water: Miscible in all dilutions

Code	Packaging
8244/42	5L
82244/51	20L

APPLICATION:

• Apply an even coat of aluminium cleaner by using a non-atomizing spray, sponge or rag to the surface being treated. It is recommended to test on the surface prior to application.

• Where applicable, the application should begin on the bottom and work up.

• Allow 3 to 15 minutes. Extreme cases of corrosion require a second application.

• Agitate the surface with a stiff bristle broom where stubborn stains persist.

WASH DOWN:

• After the corrosion or oxidation has been attacked sufficiently, flush off with a hose or agitate the surface briskly with a firm bristle brush and rinse with a stream of cold water.

• Consideration must be given to the capture and disposal of wastewater. If in doubt refer to the local water authority

• Regular Wash: Use aluminium cleaner mixed with 1:10 to 1:15 parts water.

• Light Oxidation: Use aluminium cleaner mixed with 1:7 parts water.

• Heavy-Duty Oxidation: Use aluminium cleaner mixed with 1:3 parts water.

Please Note: If unsure, always conduct a small test of the solution.

No information

Specific Gravity: 1.14 – 1.16

pH (as supplied): < 1

Water Solubility: Miscible

State: Liquid

Appearance: Clear, colourless

Strongly acidic liquid with fragrant odour.

Code	Packaging
8245/30	1L
8245/42	5L